kansascitygaragedoorspecialists.com :: 7 Tips To Replace Broken Garage Door Spring - Garage Door Repair Blogs
Tap to Call Now!
Tap to Call Now!     (816)656-3331    (913)439-5675
$75 Off Garage Door Repair Service Today!

Save Big with Exclusive Special Offers!

99
199
249
125
75
100
Half Price
200
99.95
89
149
$75 Off Garage Door Repair Service Today!

7 Tips To Replace Broken Garage Door Spring - Garage Door Repair Blogs

Posted on 2016-03-08 by Author admin

Garage door springs are among the most affected part of the garage door system. The garage door springs hold the tension and weight of the whole garage door. It permits the closing and opening of the garage door simpler. Because the garage door springs are pushed and pulled extensively and in a repetitive fashion, they happen to be worn out drastically. Hence, among all the garage parts, the garage door springs are most often substituted. If you fail to conduct garage door repair, garage door spring repair punctually, chances are the garage door might not carry out its duty or it could be the cause of accidents.

Here are some 7 Tips to Replace broken garage door spring without the help of the garage door contractor:

Step 1 It’s noteworthy to keep in mind that substituting torsion springs is a perilous undertaking if you do not have the correct tools. If you failed to do it right with the correct tools needed, you may probably lose your limb, your bare hand, or worst- your life. It’s vital that you exercise preventive measures to avoid getting injured.

The safest method to alter the older garage door springs is to create a winding bar for holes on every cone.

Step 2 Before removing the power cord from the opener, ensure that you first close the garage door. A section of the older door operators are hard wired. You might have to remove the fuse, or, flip the circuit breaker.

Step 3 As outlined, gathering the important and correct tools is vital to prevent any damages which are beyond your control. Also get adjustable wrench, vise grips, and required winding bars. These are the vital tools in performing the project. Additionally, bring a rug and a sturdy ladder which you might utilize in cleaning off your hands.

Step 4 This step incorporates a wider concept of measuring the garage torsion spring. It is vital that you compare your old garage door springs with the new garage door springs so you may get the proper springs.

Lay the garage door springs in an area where you may have a big space. Measure the inner diameter of the lengths, the springs, and the coils to identify what could be the spring’s wires. Stand the new garage door springs up in the interior of the garage door. Position the garage door springs and move them where the top end might face you. Place the left garage door spring on the left of the door and the right garage door spring on the right of the door.

Step 5 Mark the torsion shaft and drums on both ends using a marker while the garage door cables are fastened on the drums.

Step 6 This step incorporates unwinding the old garage door spring. Keep in mind not to touch the screw in case the fitting bar isn’t yet inserted correctly in the winding cone. This so as to guard you from getting injured.

Step 7 The next step involves loosening up the torsion hardware. Remove the bolts which safeguard the torsion cones to the garage door spring bracket. Slide the garage door torsion springs toward the garage door cable drums and slide it out toward the garage door drums. Between the cones, you might notice that there exists only one bearing. The goal is to prevent the shaft from wearing off with the anchor bracket.

We Service and Repair All Brands of Doors and Openers

allstar amarr chamberlain chi safe-way craftsman delden digi-code doorlink genie guardian haas-door liftmaster
linear marantec mid-america moore-o-matic multi-code northwest raynor safe-way sears skylink stanley udt wayne-dalton

Contact Info

1201 Nw Briarcliff Parkway, 2nd Flloor
Kansas City , MO 64116

Call Now! (816)656-3331  (913)439-5675